252
NeoCon Controller
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
510
OVER SPEED
A feedback speed higher than (max. rpm) x 1.1 was detected.
1. Servo pack circuit board failure
2. The motor U, V, W wiring is incorrect
3. Encoder wiring is incorrect
4. Encoder malfunction by noise
5. Excessive input, such as position or speed reference
1. Replace the servo pack
2. Check the motor wiring.
3. Check the encoder wiring.
4. Take measures against noise in encoder wiring.
5. Lower the reference value.
511
PLS OUT SPEED
Divided pulse output frequency exceeded 1.6MHz
- Check PG frequency division (Pn559).
- Lower motor speed
520
VIBRATION ALARM
Abnormal vibration was detected during motor running.
1. Abnormal vibration was detected during motor running.
2. Inertia ratio is larger than the real value.
Or it is varying in a wide range.
1-1. Reduce rotation speed.
1-2. Lower speed loop gain (Pn506).
2. Set the inertia ratio (Pn509) to an appropriate value.
710
OL(FLASHMAX)
Instantaneous rotation under overload
720
OL(RATINGMAX)
Rotate for a certain time period under a torque higher than
the rating.
1. Failure of the servo pack
2. Check motor wiring.
3. Encoder wiring is incorrect
4. The effective torque exceeds the rated torque
5. The starting torque greatly exceeds the rated or
maximum torque.
1. Replace the servo pack
2. Check motor wiring.
3. Check the encoder wiring.
4,5. Check load and operation conditions
730
DB OVERLOAD
The rotational (stopping) energy of the dynamic brake (DB)
exceeds the capacity of the DB resistor.
1. Servo pack circuit board failure
2. The rotational (stopping) energy of the dynamic
brake (DB) exceeds the capacity of the DB resistor.
1. Replace the servo pack
2-1. Lower the motor speed
2-2. Reduce the load inertia
2-3. Reduce DB stopping frequency
740
INRUSHRESOL
At the pace exceeding 10 times/2 minutes, the power supply
of the main circuit was turned ON/OFF
1. Servo pack circuit board failure
2. At the main circuit power ON/OFF, the allowable
frequency of the inrush current limit resistor was
exceeded.
1. Replace the servo pack
2. Limit the main circuit power ON/OFF frequency not
exceeding 5 times/minute.
7A0
HEATISINK HEATING
The temperature of the heat sink of the servo pack is
over 100℃.
1. Servo pack circuit board failure
2. Bad contact between servo pack PCB and thermo-switch
3. The servo pack fan stopped.
4. Rated load was exceeded.
5. The ambient temperature of the servo pack is over 55℃.
1~3. Replace the servo pack
4. Check load and operation conditions
5. Lower ambient temperature of the controller
810
ENC BACKUP ALARM
Encoder position data was cleared.
1. Servo pack circuit board failure
2. The absolute value encoder was energized for the first time.
3. Encoder cable is disconnected from the motor
4. Both the PG power (+5V) and parity power supply
in the servo pack have failed.
5. Absolute value encode failure
1. Replace the servo pack
2,3. Set up the position data in accordance with the
machine origin return method.
4. Check PG wiring. R5V power supply.
5. Replace the servo pack.
Содержание NeoCon Series
