257
Instruction Manual
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
F10
전원라인 결상 / PSUNACTIVATED
주전원 ON 상태에서 R,S,T상 내, 어느 상에서 전원이 낮은 상태
가 1초 계속
1. 서보팩의 고장
2. 삼상 전원의 배선불량
3. 삼상전원의 언발란스
1. 서보팩의 교환
2. 전원배선의 재확인
3. 전원 언밸런스 수정(상의 교체)
F20
모터선 단선 / MOTOR DISCONNECTION
모터 케이블이 단선됨
1. 모터 케이블이 단선됨
1. 모터배선 재확인
CPU00
메인 CPU 교신에러 / MAIN COMMUNI ERROR
컨트롤러의 메인모드와 서보팩의 통신 이상
1. 통신케이블의 접속불량
2. 메인보드의 고장
3. 서보팩의 고장
1. 통신케이블의 접속확인, 케이블 교환
2. 컨트롤러 교환
3. 서보팩의 교환
400
기계원점위치 미설정 / MZERO POS UN-SETUP
기계원점위치가 확립되지 않음
기계원점위치가 확립되지 않음
기계원점위치 설정 함 (기계원점위치 설정의 항 참조
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
F10
PSUNACTIVATED
While the main power is on, the voltage was low for 1 second
or longer in one or more of the R, S, and T phases.
1. Failure of the servo pack
2. Incorrect wiring of the 3-phase power supply.
3. Unbalance between the 3-phase power supply.
1. Replace the servo pack
2. Check the power supply line wiring.
3. Correct the unbalance of the power supply
(Change the phases)
F20
MOTOR DISCONNECTION
Motor cable is open.
Motor cable is open.
Check motor wiring.
CPU00
MAIN COMMUNI ERROR
Trouble in the communication between the main board of the
controller and the servo pack.
1. Bad joint in communication line.
2. Main board failure
3. Failure of the servo pack
1. Check the connection of the communication cable, or
replace it.
2. Replace the controller
3. Replace the servo pack
400
MZERO POS UN-SETUP
The start point of the machine was not set up.
The start point of the machine was not set up.
Set up the machine start point (Refer to the description on
the machine start point setting).
※ The number of servo alarm and other alarms may be the same.
This is because the alarm numbers are those of the alarms generated by the servo amp used by the controller.
In such case, verify the alarm status with the alarm message.
※ 서보알람과 다른 알람의 번호가 동일한 경우가 있지만 컨트롤러가 사용하고 있는 서보 앰프가 발생시키는 알람번호를 표시하기 때문에 이 같은
현상이 발생합니다. 그 경우에는 알람 메시지 내용으로 알람상태를 확해인주십시오.
Содержание NeoCon Series
