101
Instruction Manual
CHSEL
0,1,2,3 신호
(바이너리타입)
CHSEL 0,1,2,3
Signal
(Binary Type)
▶ 내용
① CHSEL0, CHSEL1, CHSEL2, CHSEL3과 INCOM을 ON하는 것에 의해 채널번호를 바이너리 입력할 수 있습니다.
② AUTO모드시에 바이너리 신호를 입력하는 것으로 채널번호를 선택할 수 있습니다.
단, 본 신호는 채널번호를 선택할 뿐으로 설정변경은 할 수 없습니다.
설정변경하는 경우에는 CHSET입력이 필요합니다.
▶ 조건
1. Pn030=0이고 동시에 Pn105=1일 때만 유효합니다.
2. AUTO모드에서 STATUS가 STOP 또는 RESET일 때에 변경가능합니다.
3. 채널변경완료(BLKFIN)의 출력 중 또는 G99FIN 출력중에 입력시킨 채널선택은 무효입니다.
▶ Description
① Channel No. can be entered with binaries by connecting CHSEL0, CHSEL1, CHSEL2, CHSEL3 and INCOME.
② Channel No. can be selected by entering a binary signal in AUTO mode. However, this signal can only select
the channel No. and cannot change the setting. CHSET input is required to change setting.
▶ Condition
1. Valid only when Pn030=0 and Pn105=1
2. Changeable only when the STATUS is STOP or RESET in AUTO mode.
3. The channel selection inputted during the output of the channel change finished(BLKFIN),
or during the G99 FIN output is invalid.
CHSET 신호
CHSET Signal
▶ 내용
① 바이너리 모드시에 CHSET와 INCOM을 ON하는 것에 의해 채널변경을 확정합니다.
▶ 조건
1. Pn030=0이고 동시에 Pn105=1일 때만 유효합니다.
2. 채널셋의 유효모드는 AUTO 모드시에서 STATUS가 STOP 또는 RESET 상태로 합니다.
3. CHSET 신호입력 시간은 연속 500msec이상으로 합니다.
4. 채널변경완료(BLKFIN)의 출력 중 또는 G99FIN 출력 중에 입력된 채널은 무효입니다.
5. 채널 SET 신호입력전에 CHSEL 0,1,2,3 OFF 되면 입력된 채널은 CH00입니다.
▶ Description
Channel change is confirmed by short-circuiting CHSET and INCOM in binary mode.
▶ Condition
1. Valid only when Pn030=0 and Pn105=1
2. The effective mode of channel set is when the status is STOP or RESET state in AUTO mode.
3. The CHSET signal input time shall be 500 msec or longer continuously.
4. The Channel inputted during the output of the channel change finished (BLKFIN),
or during the G99 FIN output is invalid.
12.2 출력신호
12.2 Output Signal
12.2.1 출력신호 (로터리테이블)
12.2.1 Output Signals (Rotary Table)
No.
명 칭
Name
신호명
Signal
설 명
Description
1
브레이크 +출력
Brake +output
BK+1
브레이크 조작을 위해 DC24V전원을 공급합니다.
DC 24V power supply for the brake.
2
브레이크 - 출력
Brake -output
BK-1
BK 신호
BK Signal
▶ 내용
① 언클램프 상태시에 BK+와 BK- 사이에 DC24V가 출력됩니다. BK+가 +극, BK-가 -극입니다.
② Pn029=1으로 설정한 경우에는 본 배선 간에는 항상 DC24V가 출력됩니다.
③ BK+1, BK-1은 A축용(단축용), BK+2, BK-2는 B축용을 나타냅니다.
▶ Description
① In unclamped state, DC 24V is outputted between BK+ and BK-. BK+ is the plus pole,
and BK- is the minus pole.
② If set to Pn029=1, DC 24V is always outputted between the main lines.
③ BK+ 1 and BK-1 are for A axis (single axis), BK+2 and BK-2 are for B axis.
Содержание NeoCon Series
