244
NeoCon Controller
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
107
DMDE CMD ERROR
Divide reference value is inappropriate.
The process angle of divide reference is les than 0.001°.
Correct the instructed angle/divide to 0.001 degree.
108
G27 DATA ERROR
At the execution of G27, address S, E, or R values is
inappropriate.
At the execution of G27, address S, E, or R
values is 0 or not defined.
Check the program and make correction.
109
G27 S>ERROR
The address S and E in G27 are related inappropriately.
The relationship between addresses S and E has been set to E
while executing G27.
Check the program and make correction.
110
F DATA ERROR
F data is not set on the program.
In the program, rotating speed is not set up in
the address F.
Check the program and make correction.
111
SOFTWARE LIMIT +
The present position or arrival position exceeded the limit.
1. The parameter Pn101 or Pn102 is inappropriate.
2. Wrong rotation direction
3. Defects on the program
1. Adjust the parameter.
2. Conduct manual operation correctly.
3. Check the program and make correction.
112
SOFTWARE LIMIT -
The NOT signal of the servo pack is detected in the CCW
direction.
1. The parameter Pn101 or Pn102 is inappropriate.
2. Wrong rotation direction
3. Defects on the program
1. Adjust the parameter.
2. Conduct manual operation correctly.
3. Check the program and make correction.
113
M ZERO SET ERROR
Timeout of returning to zero point
Interruption between fixtures
Command returning to zero point of the machine after removing
the interruption between the fixtures.
114
ANGLE DATA ERROR
Inappropriate program
360 degrees or above of angle was given for an absolute
reference.
Check the program and make correction.
115
G99FIN TIME - OUT
The G99 verification signal is not turned on within the specified
time.
void
116
CHANNEL SET ALARM
Error during channel setting in binary mode
1. The CHSET signal is turned off before completing the setting
of external channel.
2. Channel number beyond the setting scope
1. Keep the CHSET signal turned on for long.
2. Check the channel selection signal externally.
117
EXTMODE SEL ERROR
void
118
ILLEGAL G09
void
119
COIN SIG WIDTH ERR
No COIN signal received from the servo pack
COIN setting (Pn617) of the servo pack kept low
The 1 Parameter Pn617 (Servo pack P522) settings have been
changed.
Содержание NeoCon Series
