51
Instruction Manual
[About the Address A (Angle of Rotation)]
● If A was not set up, the loop escape commandof G25 is not executed. Therefore,
『Err 317 EDIT ILLEGAL G (negative G Code)』 alarm is triggered.
● See『Type without G Code (Standard)』 for other details.
[About the Address J (Jump)]
● If no J setting, G25 command is invalid. Finish the block and then proceed to the next block.
● If J is set up with block No., jump to the designated block after finishing the present block.
[About the Address F (Speed of Rotation)]
[About the Address D (No. of Equal Partition)]
● See『Type without G Code (Standard)』
[어드레스A(회전각도)에 관하여]
● A의 설정이 없는 경우 G25의 루프탈출이 실시되지 않게 되므로『Err317 EDIT ILLEGAL G(부정 G코드)』의 알람이 발
생합니다.
● 그 외의 내용은『G코드 없는 타입』과 같은 내용입니다.
[어드레스J(점프)에 관하여]
● J의 설정이 없는 경우 G25지령은 무효이고 블록완료 후 다음 블록으로 진행됩니다.
● J에 블록번호 설정이 되어 있는 경우는 블록완료 후 지정 블록번호로 블록 점프합니다.
[어드레스F(회전속도)에 관하여]
[어드레스D(등분할수)에 관하여]
● 『G코드 없는 타입(표준)』참조.
Explanation
해설
[프로그램 포맷]
G25
A_F_D_J_
굵은선 비스듬한 문자부분은 생략가능을 나타냅니다.
G25 : 루프 탈출 지령
A
: 회전각도
설정단위
: deg
설정범위
: ±999.999 (인클리멘탈시)
±0~359.999 (앱솔루트시)
F
: 회전속도
설정단위
: 0.01min
-1
설정범위
: 0~9999
D
: : 등분할수
설정범위
: 0~99
J
: : 프로그램점프 대상
설정범위
: -1,0~999
J-1
: 서브프로그램 리턴지령
[Program Format]
G25
A_F_D_J_
Thick Italic letters represent the omissible parts.
G25 : Loop Escape Command
A
: Angle of rotation
Setting unit
: deg
Setting range : ±999.999 (At incremental)
±0~359.999 (At absolute)
F
: Speed of rotation
Setting unit
: 0.01min
-1
Setting range : 0~9999
D
: No. of equal partitions
Setting range : 0~99
J
: Object of program jump
Setting range : -1,0~999
J-1
: Subprogram return command
Содержание NeoCon Series
