242
NeoCon Controller
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
013
MEMORY WRITE ERR
Error while storing data in the memory
Error while storing data in the memory
Turn power off, and then on after at least 10 seconds.
014
MOTOR WRITE ERR
Error in data writing on the motor control chip
Deviation of information between the motor control CPU and the main CPU
Turn power off, and then on after at least 10 seconds.
015
MEMORY CHECK ERR
Error while checking memory after turning power on
1. Excessively low or high temperature inside the controller
2. Memory damaged
1.
Check the temperature inside the controller after turning power off.
2. replace or repair the momory
016
POWER OFF ALARM
Parameter change requiring turning power on again
1. A parameter which require system restart was changed.
2. A parameter was entered from outside.
3. A servopack parameter which require system restart
was changed.
Turn power off, and then on after at least 10 seconds.
017
POWER ON ERROR
Power on procedure failed.
Failed to process the data obtained at power on.
Reset or turn power off, and then on after at least 10 seconds.
018
CH SIGNAL ON FAULT
Turn the CHSET signal off, and then press the Reset button.
019
ALARM AL01, AL02, AL03
One or more of the output signals of the servo pack (AL01,
AL02 and AL03) is kept turned on.
Alarm code is displayed from the servo pack when starting the servo pack.
Remove the cause of alarm, and then press the Reset button.
101
ORG_POS SET REQ
Setting the zero point of the machine is required.
Instructed the movement command before setting the zero
point of the machine
Resume operation after setting the zero point of the machine.
102
WORK ZERO ALARM
The machining zero point has been instructed before setting the
zero point of the machine.
Movement to the machining zero point has been instructed
before setting the zero point of the machine.
Return to the machining zero point after the instruction of
returning to the zero point of the machine.
103
STACK UNDERFLOW
Inappropriate program
Without executing subroutine call, executed subroutine
return by J-1.
Check the program and make correction.
104
STACK OVERFLOW
Inappropriate program
1. Nesting exceeded 50 by the repetition of G27.
2. Executed a jump command during subroutine call.
Check the program and make correction.
105
NOT RETURN ALARM
Inappropriate program
At the subroutine call by address J, return command
was not executed at the last block J-1.
Check the program and make correction.
106
POS TIME OVER
The motor has rotated by external force during clamping, and
the allowable position deviation has been exceeded.
1. Overloaded.
2. Droop check setting time (Pn008) is too short.
3. Droop check setting amount (Pn009) is too small.
1. Reduce the load.
2. Set up the droop check time above the acc/dec time.
3. Increase the droop check setting.
107
DMDE CMD ERROR
Divide reference value is inappropriate.
The process angle of divide reference is les than 0.001°.
Correct the instructed angle/divide to 0.001 degrees.
Содержание NeoCon Series
