246
NeoCon Controller
Alarm
Rank
Message
Description
Possible Cause
Countermeasures
201
NC ADDRESS ERROR
Inappropriate transmission program
An address which does not exist was transmitted.
Check the transmission, correct it if necessary.
202
NC AXIS ERROR
Inappropriate transmission program
Axle specifying (A or B) alarm
Check the transmission, correct it if necessary.
203
NC SET RANGE OVER
Inappropriate transmission program
Inappropriate address setting value in the NC program
Check the transmission, correct it if necessary.
204
NC CHANNEL ERROR
Inappropriate transmission program
Inappropriate address setting value in the NC program
Check the transmission, correct it if necessary.
205
NC BLOCK NO ERROR
Inappropriate transmission program
Inappropriate address setting value in the NC program
Check the transmission, correct it if necessary.
206
NC COMMAND ERROR
Inappropriate transmission program
In internal process, incorrect G code was executed.
Resume operation after the reset release.
207
RS232C H/W ALARM
Inappropriate transmission program
The received message of host communication
exceeded 256 characters.
Limit the communication data not longer than 256 characters.
208
FRAMING ALARM
Program G code input error
Bit rate kept deviating
Match the communication protocol.
209
-
-
-
-
210
ILLEGAL CMD ALARM
Inappropriate remote controller (RC) transmission command
Received a host command not pertinent to RC.
Check the transmission command from the machine,
correct it if necessary.
211
NO COMMAND ALARM
Inappropriate remote controller (RC) transmission command
Check the transmission command from the machine,
correct it if necessary.
212
ILLEGAL G ADDR
Inappropriate remote controller (RC) transmission command
1. There existed the addresses not corresponding
to the G code.
2. Received an inexistent G code in RC mode.
Check the transmission command from the machine,
correct it if necessary.
213
OVER - RUN ALARM
Inappropriate remote controller (RC) transmission command
Reception buffer is full.
Release the reset.
214
CMD ILLEGAL MODE
Inappropriate remote controller (RC) transmission command
The operation mode is not AUTO or SINGLE.
The functions of remote control should be performed in Auto
and Single modes.
Содержание NeoCon Series
