Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 46

Страница: 46 / 456

2.26

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Coolant Strength / Type

Test the strength of the coolant using an antifreeze
hydrometer.

• A 50/50 or 60/40 mixture of antifreeze and distilled

water will provide the optimum cooling, corrosion
protection, and antifreeze protection.

• Do not use tap water, straight antifreeze, or

straight water in the system. Tap water contains
minerals and impurities which build up in the
system.

• Straight water or antifreeze may cause the system

to freeze, corrode, or overheat.

Polaris 60/40 Anti-Freeze/ Coolant

(PN 2871323)

Coolant Drain / Fill

Coolant Drain

Remove the front cover located under the front rack,
right inner fender and footwell plastics.

Slowly remove the pressure cap (1) to relieve any
cooling system pressure.

WARNING

Never drain the coolant when the engine and radiator

are warm or hot. Hot coolant can cause severe burns.

Allow engine and radiator to cool.

Place a suitable drain pan underneath the radiator
fitting on the front right-hand side of the vehicle.

Drain the coolant from the radiator by removing the
lower coolant hose (1) from the radiator as shown.
Properly dispose of the coolant.

Allow coolant to completely drain.

MAINTENANCE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды