Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 456

background image

2.16

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

ENGINE

Engine Oil Level

Access the oil dipstick and fill tube from the right side of
the ATV. A rising oil level between checks in cool weather
driving can indicate contaminants such as gas or mois-
ture collecting in the crankcase. If the oil level is over the
full/safe mark, change the oil immediately.

1.

Set machine on a level surface.

2.

Clean the area around the dip stick.

3.

Remove dipstick and wipe dry with a clean cloth.

4.

Reinstall dipstick completely.

NOTE: The dipstick must be screwed completely
in to ensure accurate measurement.

5.

Remove dipstick and check to see that the oil level is
in the normal range (2). The oil should be between
the top line and the bottom line on the dipstick. Add
oil as indicated by the level on the dipstick. Do not
overfill.

NOTE: Rising oil level between checks in cool
weather driving, can indicate moisture collecting
in the oil reservoir. If the oil level is over the full
mark, change the oil.

Oil and Filter Change

Always change the oil and filter at the intervals outlined in
the Periodic Maintenance Chart. Always change the oil
filter whenever changing oil.

Oil Filter Torque:

Turn by hand until filter gasket

contacts sealing surface, then

turn an additional 1/2 turn

Oil Filter Wrench:

PV-50105

Recommended Engine Oil:

Polaris PS–4

Synthetic 5W-50

CAUTION

Personal injury can occur when handling used oil. Hot

oil can cause burns or skin damage.

NOTICE: Care must be taken to ensure that the fluids
are contained. Be prepared to collect the fluid with
suitable containers before opening any compartment
or disassembly of any component containing fluids.

1.

Place vehicle on a level surface.

2.

Place the transmission in PARK (P).

3.

Clean area around drain plug at bottom of oil pan.

4.

Start the engine. Allow it to warm up at idle for two to
three minutes.

5.

Stop the engine.

6.

Place a drain pan under the crank case.

MAINTENANCE

«
...
34
35
36
37
38
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: KAYO MOTO Страницы: 6

Бренд: FEATHERLITE TRAILERS Страницы: 78

JACOBSEN 4800 2006+

Бренд: E-Z-GO Страницы: 114

Бренд: Can-Am Страницы: 144

Бренд: Taylor-Dunn Страницы: 216

Бренд: Kellfri Страницы: 8

Бренд: Yamaha Страницы: 98

Бренд: Jacobsen Страницы: 64

Бренд: Arctic Cat Страницы: 124

Can-Am Defender DPS HD10

Бренд: BRP Страницы: 244

BOMBARDIER DS250 2006

Бренд: BRP Страницы: 284

Бренд: Baja motorsports Страницы: 44

Бренд: Yamaha Страницы: 287

Бренд: Eagle Страницы: 24

Бренд: FLEMING Страницы: 10

Бренд: Fruehauf Страницы: 64

Бренд: Aeon Страницы: 93

Бренд: Aeon Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды