Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 456

background image

4

4.15

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

8.

If voltage at the plug was within the specified range,
and there was continuity across the pump terminals,
reconnect the plug to the fuel pump, making sure you
have a clean connection. Turn on the key switch and
listen for the pump to activate.

NOTE: If the pump starts, repeat steps 3, 4 and 5
to verify correct pressure.

9.

If the pump still does not operate, check for correct
ECU operation by plugging in a known-good ECU of
the same model.

NOTE: If the pump still does not operate, replace
the fuel pump assembly.

10. Re-instal the front cab.

Fuel Pump Replacement

WARNING

Always wear safety goggles when working with high

pressure or flammable fluids. Failure to do so could

result in serious injury or complications.

1.

Remove the seat and front cab.

2.

Disconnect the battery (-) negative cable.

3.

Ensure that static has been discharged from you by
touching a ground source such as the engine or
frame.

4.

Disconnect the fuel pump electrical harness(1).

5.

While holding a shop towel over the fuel line
connector, disconnect the quick connect fuel line (2)
from the fuel pump.

CAUTION

It is possible for pressurized fuel to be present when

disconnecting the fuel line.

It is recommended to allow the vehicle to sit for a period

of one hour after shutting off the engine before

servicing the fuel pump. This allows the exhaust to cool

and fuel pressure to drop.

NOTE: A small amount of fuel may come out of
the fuel line or tank. Properly drain fuel into a
suitable container.

6.

Be sure the top of the fuel tank is clean. If it requires
cleaning, hand wash the top of the tank to ensure no
debris will enter the fuel system when the fuel pump
is removed.

WARNING

Failure to clean area around fuel pump may lead to

debris entering the fuel tank during service. Excessive

debris in fuel tank may cause premature wear of fuel

pump and/or clogging

of internal fuel filters.

FUEL SYSTEM - GENERAL

«
...
159
160
161
162
163
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: JLG Страницы: 62

Twister UM250IIR

Бренд: Hammerhead Страницы: 67

Бренд: Wilson Electronics Страницы: 3

Бренд: Suzuki Страницы: 382

Бренд: Morooka Страницы: 134

Бренд: Aosom Страницы: 5

Бренд: Yamaha Страницы: 213

Бренд: Yamaha Страницы: 282

Бренд: Yamaha Страницы: 443

Бренд: Ultra-tow Страницы: 9

Rexus 5000 Series

Бренд: Humbaur Страницы: 28

Бренд: Baja Страницы: 6

Бренд: Tatu Marchesan Страницы: 48

Warrior YFM350XRC

Бренд: Yamaha Страницы: 174

Бренд: PARKIT360 Страницы: 13

Бренд: BERG Страницы: 8

Бренд: Westbrook Trailers Страницы: 24

ALTERRA MUD PRO 700 LTD EPS 2018

Бренд: Textron Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды