Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 109

Страница: 109 / 456

3.51

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Piston-to-Cylinder Clearance

Measure the outside diameter of the piston 12 mm
from the skirt and at a right angle to the direction of
the piston pin (Item 1).

Subtract this measurement from the maximum
cylinder size measurement from cylinder inspection.

Piston to Cylinder Clearance:

.00019 - .00216″ (.005 - .055 mm)

Piston O.D.:

3.8957 - 3.8968″ (98.953 - 98.980 mm)

Piston / Rod Inspection

Measure piston pin bore inside diameter I.D.(Item 1).

Piston Pin Bore:

Std.: 0.8662 - 0.8665″ (22.004 - 22.010 mm)

Service Limit: 0.8651″ (21.975 mm)

Measure piston pin O. D (2). Replace piston and/or
piston pin if out of tolerance.

Piston Pin O.D.:

Std.: 0.8659 - 0.8661″ (21.995 - 22.0 mm)

Service Limit: 0.8651″ (21.975 mm)

Measure connecting rod small end ID. Inspect
bearing surface for damage.

Piston Pin Degree of Fit:

Pin should be a push-fit by hand with piston at

room temperature or warmed slightly

Connecting Rod Small End ID:

Std.: 0.8665 - 0.8670″ (22.010 - 22.023 mm)

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды