Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 35

Страница: 35 / 456

2.15

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Crankcase Breather Valve / Hose

The breather valve is on the hose that runs between the
engine and air box. Be sure breather line is routed prop-
erly and secured in place.

Remove the left side panel

Remove the hose clamps from the valve and pull the
valve out of the hoses.

Inspect the valve for debris. Blow gently through the
valve to check for clogging. Replace a damaged or
clogged valve.

NOTE:

In-line breather filter service life is

extended when the foam air box pre-filter is in
place and maintained properly. Never operate the
engine without the pre-filter.

Check the hoses for cracks, deterioration, abrasion,
or leaks. Replace as needed.

CAUTION

Make sure lines are not kinked or pinched.

Reinstall the valve and hose clamps.

CAUTION

Operation of your vehicle without a breather valve can

cause engine damage. Always reinstall the breather

valve after removing it for service.

Install the left side panel

MAINTENANCE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды