Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 63

Страница: 63 / 456

3.5

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Oil Pressure Test

Attach the Oil Pressure Gauge Adapter (PU-50569)
to the Oil Pressure Gauge (PV-43531).

Oil Pressure Gauge Adapter: PU-50569

Oil Pressure Gauge: PV-43531

Remove the seat, Left footwell, and left side pannel.

Clean the area around the main oil gallery plug (1),
located on the oil filter adapter housing.

Remove the plug (1) and insert the oil pressure
adapter.

Start engine and allow it to reach operating
temperature, monitoring gauge indication.

NOTE: Test results are based on the use of the
recommended

engine

oil

(Polaris

PS-4)

operating

temperature,

and

may

vary

considerably if any other oil is used or if engine
is not up to temperature.

Oil Capacity:

Approx. 2 Quarts (1.9 L)

Oil Filter Wrench:

PU-50105 or 2.5” (64 mm)

Oil Type:

Polaris PS-4

Synthetic Engine Oil

Oil Pressure

Minimum Specification:

(using Polaris PS-4 Plus at operating temperature)

10 PSI @ 1200 RPM (Minimum)
40 PSI @ 7000 RPM (Minimum)

Upon assembly, torque the crankcase gallery plug to
specification.

Oil Gallery Plug:

11 ft-lbs (15 Nm)

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды