Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 221

Страница: 221 / 456

5.27

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

EPS Unit Removal (EPS Models)

Remove the front rack or front storage box and front
cover.

Remove both front mud guards, upper side panels,
front cab and right-hand footwell .

Remove the fuel tank.

Remove the pinch bolts retaining the upper steering
post to the power steering unit.

NOTE: Some models, feature a lower steering
shaft pinch bolt (1 and 2). Remove pinch bolt.

Disconnect the (2) electrical harnesses from the
power steering unit.

Remove the fasteners retaining the upper steering
post bushing bracket.

Lift the upper steering post up from the power
steering unit.

Remove the (4) mounting fasteners that retain the
power steering unit and mount plate to the frame.

Carefully lift the power steering unit up to disengage
the lower steering coupler and remove it from the
chassis.

EPS Unit Installation (EPS Models)

Position the vehicle so the front wheels are pointing
straight forward.

Clean the lower steering post so the alignment mark
is visible. Mark the skip tooth spline on the lower
power steering shaft.

Apply anti-seize to the shaft splines to aid assembly.

BODY / STEERING / SUSPENSION

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды