Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 456

background image

2.20

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Exhaust Pipe

WARNING

Do not perform clean out immediately after the engine

has been run, as the exhaust system becomes very

hot. Serious burns could result from contact with

exhaust components.

To reduce fire hazard, make sure that there are no

combustible materials in the area when purging the

spark arrestor.

Wear eye protection.

Do not stand behind or in front of the vehicle while

purging the carbon from the spark arrestor.

Never run the engine in an enclosed area.Exhaust

contains poisonous carbon monoxide gas.

Do not go under the machine while it is inclined.Set the

hand brake and block the wheels to prevent roll back.

Failure to heed these warnings could result in serious

personal injury or death.

The exhaust pipe must be periodically purged of
accumulated carbon as follows:

1.

Remove the clean out plugs located on the bottom of
the muffler.

2.

Place the transmission in Park and start the engine.
Purge accumulated carbon from the system by
momentarily revving the engine several times.

3.

If some carbon is expelled, cover the exhaust outlet
and lightly tap on the pipe around the clean out plugs
with a rubber mallet while revving the engine several
more times.

4.

If particles are still suspected to be in the muffler,
back the machine onto an incline so the rear of the
machine is one foot higher than the front. Set the
hand brake and block the wheels. Make sure the
machine is in Park and repeat Steps 2 and 3.

SEE

WARNING

5.

If particles are still suspected to be in the muffler,
drive the machine onto the incline so the front of the
machine is one foot higher than the rear. Set the
hand brake and block the wheels. Make sure the
machine is in Park and repeat Steps 2 and 3.

SEE

WARNING

6.

Repeat steps 2 through 5 until no more particles are
expelled when the engine is revved.

7.

Stop the engine and allow the arrestor to cool.

8.

Reinstall the clean out plugs.

MAINTENANCE

«
...
38
39
40
41
42
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Bad Boy Страницы: 132

Бренд: ODES UTVS Страницы: 34

Бренд: B.O.B Страницы: 36

Бренд: Ezgo Страницы: 102

Бренд: Sakai Страницы: 77

Бренд: Kazuma Страницы: 36

Бренд: Miller Electric Страницы: 20

Бренд: NorAM Страницы: 118

Бренд: PRONAR Страницы: 125

Бренд: SSR Motorsports Страницы: 55

Бренд: GSMOON Страницы: 49

K2 QUAD 250 - SERVICE

Бренд: GAS GAS Страницы: 64

GRIZZLY YFM70GPAN

Бренд: Yamaha Страницы: 180

Бренд: Land Pride Страницы: 96

Бренд: Landa Страницы: 14

Бренд: Panasonic Страницы: 91

Бренд: Panasonic Страницы: 388

Бренд: Primo Water Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды