Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 77

Страница: 77 / 456

3.19

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

3. Remove the upper radiator retaining bolts and the

bolts retaining the lower radiator mount bracket.
Remove the bracket from the frame.

4. Disconnect the fan motor and remove the radiator

from the vehicle. Take care not to damage the cooling
fins.

5. Reverse procedure for installation.

Thermostat Replacement

Remove the left side panel and PVT intake / exhaust
ducting as required.

WARNING

The cooling system is under pressure and serious

burns may result.

Allow the engine to cool before servicing.

Remove front rack , front cab and fuel tank . (not
required for touring models)

Remove the pressure cap to relieve any system
pressure (see “Pressure Cap Test”).

Drain coolant to a level below the thermostat
housing.

Remove the spark plug wire from the engine.

Remove the (2) bolts (X) retaining the thermostat
cover.

NOTE: Image For Reference Only.

Lift the cover from the engine and remove the
thermostat.

Reverse this procedure for installation. Replace
thermostat

seal

worn

damaged.

Torque

thermostat cover bolts to specification.

Thermostat Cover Bolts:

7.5 ft-lbs (10 Nm)

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды