manualshive.com logo in svg

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Polaris Sportsman 570 EF 2014 - выпуск модели с мощным двигателем и спортивным дизайном. На нашем сайте вы можете бесплатно загрузить руководство по обслуживанию, чтобы всегда быть в курсе обслуживания вашего ATV. Скачайте его с manualshive.com прямо сейчас.

Поделиться
Скачать
background image

4

4.21

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

4.

While holding a shop towel over the fuel line
connector, disconnect the quick connect fuel line (2)
from the fuel pump. Move the fuel line out of the way
for tank removal.

NOTE: A small amount of fuel may come out of
the fuel line or tank. Properly drain fuel into a
suitable container.

5.

Remove the fuel tank vent hose clamp (3) with a
suitable pliers and remove the vent line from the tank
vent fitting.

6.

Remove the two fuel tank mounting bolts at the rear
of the gas tank.

7.

Carefully pull the fuel tank out of the frame. Keep the
fuel tank horizontal during removal, this will keep the
fuel in the tank from spilling out the top inlet.

Fuel Tank Installation

1.

Carefully reinstall the fuel tank assembly.

2.

Reinstall the fuel tank brackets and fasteners.

3.

Install the fuel line, vent hose and clamp. Verify they
are secure.

4.

Reconnect the fuel pump electrical harness.

5.

Reconnect the negative battery cable. Test the fuel
pump by turning the ignition key on and listening for
the pump to activate. Check for leaks.

6.

Reinstall the PVT exhaust duct, air box top, front cab,
side panels and seat.

Fuel Lines - Quick Connect

1.

Place a shop towel around the fuel line to catch any
dripping fuel. Squeeze the connector tabs together
and push the locking slide back.

2.

Pull on the fuel line for removal.

3.

To install the line(s), verify the connections are clean
and free of debris.

4.

Snap the fuel line back over the nipple and slide the
locking mechanism back into place. Verify the
connector tabs snap back into place.

FUEL SYSTEM - GENERAL

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Honda FourTrax Foreman Rubicon TRX500FA5 2019 Owner'S Manual preview
FourTrax Foreman Rubicon TRX500FA5 2019
Бренд: Honda Страницы: 291
Labrie expert 2000 Maintenance Manual preview
expert 2000
Бренд: Labrie Страницы: 172
CadKat PowerHawk User Manual preview
PowerHawk
Бренд: CadKat Страницы: 11
Honda 1988 TRX 300 FW Owner'S Manual preview
1988 TRX 300 FW
Бренд: Honda Страницы: 84
Dazon Buggy Raider mini 90D Service Manual preview
Buggy Raider mini 90D
Бренд: Dazon Страницы: 60
TrailMax FWTD-50-T Manual preview
FWTD-50-T
Бренд: TrailMax Страницы: 58
Verhagen Leiden V-move EDV User Manual preview
V-move EDV
Бренд: Verhagen Leiden Страницы: 17
Arrowquip CHUTE TRAILER Product Manual preview
CHUTE TRAILER
Бренд: Arrowquip Страницы: 16
Rato RT150ST-A Service Manual preview
RT150ST-A
Бренд: Rato Страницы: 118
Ifor Williams Trailers TT85G Operator'S Manual preview
TT85G
Бренд: Ifor Williams Trailers Страницы: 16
BOMBARDIER 1988 Citation LS Operator'S Manual preview
1988 Citation LS
Бренд: BOMBARDIER Страницы: 52
BOMBARDIER 1999 Traxter Operator'S Manual preview
1999 Traxter
Бренд: BOMBARDIER Страницы: 80
Yamaha WOLVERINE YXE70WPXH Owner'S Manual preview
WOLVERINE YXE70WPXH
Бренд: Yamaha Страницы: 186
Yamaha YFM4FAR Service Manual preview
YFM4FAR
Бренд: Yamaha Страницы: 397
Yamaha SXV70H Owner'S Manual preview
SXV70H
Бренд: Yamaha Страницы: 98
Yamaha YXR660FAS Owner'S Manual preview
YXR660FAS
Бренд: Yamaha Страницы: 154
Yamaha Vector RS90GTA Owner'S Manual preview
Vector RS90GTA
Бренд: Yamaha Страницы: 140
Zap DUDE 2010 Owner'S And Operator'S Manual preview
DUDE 2010
Бренд: Zap Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды