Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 370

Страница: 370 / 456

9.26

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove caliper mounting bolts and lift caliper off of
disc.

NOTE: When removing caliper, be careful not to
damage brake line. Support caliper so as not to
kink or bend brake line.

Push caliper pistons into caliper bore slowly with
pads installed.

Remove the caliper slide pins and remove the brake
pads from the caliper.

Clean the caliper with brake cleaner or alcohol.

Measure the thickness of the pad material. Replace
pads if worn beyond the service limit.

Rear Brake Pad Thickness

Service Limit: .180” (4.6 mm)

Sportsman Rear Pad Installation

Install new brake pads in caliper body.

WARNING

If the brake pads are contaminated with grease,

oil, or liquid soaked do not use the pads,

use only new clean pads.

Install and tighten the slide pin with a hex wrench.

BRAKES

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды