Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 229

Страница: 229 / 456

5.35

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove wheel nuts and wheels.

Remove cotter pin (A) from ball joint castle nut (B).

Remove castle nut (B) and separate A-arm (C) from
ball joint stud.

Remove screws (D) and ball joint retaining plate (E).

Use the Ball Joint Replacement Tool (PN 2870871),

remove

ball joint (F) from strut housing. Refer to

photos.

Install puller guide (G) with extension cap (H).

Apply grease to extension cap and threads of puller
bolt to ease removal.

10. Thread bolt (J) with nut (I) onto ball joint stud as

shown.

11. Apply heat to ease removal.

12. Hold bolt (J) and turn nut (I) clockwise until ball joint

is removed from strut housing.

13. To

install

a new ball joint, Remove extension cap and

attach puller guide using short bolts provided in the
kit.

14. Remove extension cap and attach puller guide using

short bolts provided in the kit.

15. Insert new ball joint (K) into driver (L).

16. Slide ball joint/driver assembly into guide.

17. Apply heat to ease installation.

18. Drive new joint into strut housing until fully seated.

19. Apply Loctite™ 242

(PN 2871949)

to threads of

retaining plate screws or install new screws with pre-
applied

locking

agent.

Torque

screws

specification.

Retaining Screws:

8 ft-lbs (11 Nm)

20. Install A-arm on ball joint and torque castle nut to

specification.

Castle Nut:

30 ft-lbs (41 Nm)

21. Reinstall cotter pin with open ends toward rear of

machine.

BODY / STEERING / SUSPENSION

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды