Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 197

Страница: 197 / 456

5.3

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

BODY

Side Panel Removal

Side panel removal is quick and easy, use the following
instructions for removal and installation.

Grasp one side of the seat near the rear edge.

Pull upward abruptly to disengage the under-seat
fasteners.

Remove the seat.

Remove the plastic rivets securing the side panel.

Grasp the rear of the side panel near the rear cab.
With a firm motion, pull the side panel outward to
remove the side panel.

Reinstall the side panel by reversing the removal
procedure.

Front Storage Box Lid / Front Rack and
Access Panel Removal / Installation

Open the front rack storage area.

Remove the (4) T-25 screws securing the access
cover to the front cab as shown below.

Move the seal out of the sealing channel and pull up
on the front of the access cover. Remove the access
cover.

Remove the safety cables that are attached to the
front cab and to the front storage box lid / front rack.

Remove the (2) T-27 screws that attach the front
storage box lid / front rack to the front bumper.

BODY / STEERING / SUSPENSION

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды