Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 139

Страница: 139 / 456

3.81

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

MAG Side Crankcase Bearing Service

Bearing Removal

Support the crankcase and drive, press, or extract
the balance shaft bearing (2) with a blind bearing
remover.

WARNING

The MAG side crankshaft plain bearing(1) is not

serviceable. Crankcase replacement is required if the

bearing is damaged or has excessive wear. The

crankshaft is reusable if it meets specifications and

MAG side bearing surface is not groved, pitted,

damaged or excessively worn.

Due to extremely close tolerances and minimal wear,

the bearings must be inspected visually, and by feel.

Look for signs of discoloration, scoring or galling. Turn

the inner race of each bearing. The bearings should

turn smoothly and quietly. The outer race of each

bearing should fit tightly in the crankcase. The inner

race should be firm with minimal side to side movement

and no detectable up and down movement.

Bearings are stressed during the removal process and

must not be re-used!

Installation

Clean all bearing bores and inspect for excessive
wear.

Lubricate all bearing bores with clean engine oil.

Fully seat the

new

balance shaft bearing until

bottomed in the bearing bore.

Oil Pickup Assembly Inspection

The oil pickup assembly is located inside of the oil pan.

Remove fastener that retains oil pickup.

Pull and twist to remove the oil pickup assembly from
the crankcase.

Inspect the assembly for cracks and excessive wear.
Replace if necessary.

Thoroughly clean the pickup assembly.

Press the pickup assembly into the crankcase until
fully seated in bore.

Install fastener that retains the oil pickup; torque to
specification.

WARNING

Do Not Exceed Torque Value.

Oil Pickup:

59.75 in-lbs ± 6 in-lbs (6.75 Nm ± 0.7 Nm)

Oil Pressure Regulator (Bypass) Valve
Inspection

The oil pressure regulator (bypass) valve is located in the
MAG side crankcase (B).

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды