Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 266

Страница: 266 / 456

6.32

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Moveable Sheave - Bushing Installation

Working from the top, insert Puller Adapter (#10) (PN
5020633) onto the puller.

Start new bushing evenly in moveable sheave. Apply
Loctite™ 680 to the back side of new bushing.

Install sheave onto puller with new bushing upward
as shown. Install Puller Adapter (#10) (PN 5020633).

Install nut onto puller rod and hand tighten against
installation tool.

Turn clutch sheave counterclockwise until bushing is
seated.

Remove nut from puller rod and set aside.

Remove installation tool and clutch sheave from
puller.

Repeat installation procedure for other moveable
bushing.

Install new ramp buttons into the sheave. Apply
thread

locking

agent

the

fasteners.

Install

fasteners and tighten securely.

CLUTCHING

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды