Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 278

Страница: 278 / 456

6.44

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

DRIVEN CLUTCH BUSHING SERVICE

Bushing Service (NON EBS and EBS)

IMPORTANT: Special Tools Required

EBS Clutch Bushing Tool Kit - 2201379

ITEM

QTY.

PART DESCRIPTION

PART #

A, B

EBS Puller Tool

5132027

EBS Puller Nut

5132501

EBS Main Adapter

5132029

EBS Bushing Removal
Tool Instructions

5132028

–

Instructions

9915111

Additional Special Tools

QTY.

PART DESCRIPTION

PART #

Clutch Bushing Replacement Tool
Kit

2871226

Piston Pin Puller

2870386

*Clutch Bushing Replacement Tool Kit (PN 2871226

)

ITEM

QTY.

PART DESCRIPTION

PART #

P-90 Drive/Driven
Clutch Bushing Install
Tool

5020628

Drive Clutch Cover
Bushing Removal/
Installation Tool (all
clutches)

5020629

P-90 Driven Clutch
Cover Bushing
Removal Tool

5020631

Main Puller Adapter

5020632

Adapter Reducer

5010279

#10

Number Two Puller
Adapter

5020633

Bosch Automotive Service Solutions- 1-800-328-6657 or

http://polaris.service-solutions.com

NOTE: Bushings are installed at the factory using
Loctite® 648. In order to remove bushings it will be
necessary to apply heat evenly to the area around
each bushing. Clean all residual Loctite™ from
bushing bore prior to installing new bushing.

Clutch Bushing Removal

Clutch components will be hot! In order to avoid serious
burns, wear insulated gloves during the removal process.

Install main puller adapter (Item 8) onto puller.

Install adapter reducer (Item 9).

Using a hand held propane torch, apply heat around
outside of bushing until tiny smoke tailings appear.

Flip sheave over so bushing faces downward and
install onto puller.

Install bushing tool (Item 2).

CLUTCHING

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды