Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 404 | Manualshive

Страница: 404 / 456

background image

10.24

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

ELECTRONIC POWER STEERING (EPS)

EPS Operation

The EPS module is an intelligent electronic power
steering system that operates off of the vehicle’s 12V
electrical system. It calculates steering assist by sensing
the difference between the input torque of the steering
post and the output torque required to turn the wheels,
and then provides assist by energizing an electric motor.
The process provides a smooth, seamless assist.

The system is continuously running diagnostic checks
and monitoring factors such as battery voltage, ground
speed and engine speed. In the event an internal or
external issue that affects the EPS system is detected,
the system will illuminate a fault indicator and transition
to a normal mechanically coupled steering system. The
system is Polaris Digital Wrench® compatible for
simplified

diagnostics

and

system

troubleshooting

through the vehicle’s diagnostic port.

With the engine off and the key on, the power steering
unit will operate for up to five minutes. After the five
minutes, you will need to cycle the key switch and restart
the engine to regain power steering operation.

The Power Steering 30A Fuse.

• If the fuse fails, the Power Steering Malfunction

Indicator Light (MIL) on the instrument cluster will
illuminate. During this time, the vehicle will have
no power steering operation. You will be able to
connect and communicate with the vehicle’s
Engine Controller, but not the Power Steering
Controller, while using Digital Wrench®.

NOTE: DO NOT SPLICE OR CUT INTO THE
CAN CIRCUITS.

CAUTION

Electronic Power Steering (EPS) units are not

interchangeable between ATV and

RANGER

product

lines.

NOTE:

Refer

to

Chapter

10

“Steering

/

Suspension” for power steering unit removal
and

installation

procedures.

Removal, page 5.27

WIRE COLOR

FUNCTION

ORANGE

Key-On / Run Switch On
Battery Voltage / EPS Power

RED

Battery Voltage

BROWN

Ground

YELLOW

CAN High Signal

GREEN

CAN Low Signal

Proper EPS System Diagnosing

READ BEFORE YOU REPLACE THE EPS UNIT!

NOTE: Try to reflash the EPS unit before attempting
to replace it. A simple reflash may be all that is
needed to repair the EPS problem. Always reflash
the EPS unit as the first step in diagnosing an EPS
problem.

EPS Circuit

NOTE:

Refer to “Cooling Fan & EPS” breakout

diagram near the end of this Chapter.

ELECTRICAL

«
...
402
403
404
405
406
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Jayco Страницы: 87

Бренд: Eton America Страницы: 96

Бренд: KYMCO Страницы: 89

Utility Vehicle Workshop

Бренд: Bush Hog Страницы: 11

Бренд: Vermeer Страницы: 88

Off-Roader 36EL

Бренд: Texas Страницы: 27

Бренд: AC Air Technology Страницы: 46

2007 Outlander 500 EFI

Бренд: Can-Am Страницы: 148

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 92

WARRIOR YFM350XN

Бренд: Yamaha Страницы: 167

Бренд: Yamaha Страницы: 227

Бренд: Yamaha Страницы: 288

Бренд: Yamaha Страницы: 360

Бренд: Yamaha Страницы: 439

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды