Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 456

background image

3

3.85

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Balance Shaft Installation / Timing

1.

Position balance shaft in the crankcase.

2.

Rotate crankshaft to align the timing marks (A) as
shown below.

3.

Fully seat the balance shaft into the crankcase and
verify timing marks are correct.

Final Crankcase Assembly

1.

Prepare MAG side crankcase by cleaning sealing
surface. Be sure the oil pickup and oil pressure valve
are fully installed.

2.

Apply a thin film of Crankcase Sealant (PN 2871557)
evenly to a clean and oil-free MAG crankcase mating
surface as indicated below (1). Be sure alignment
pins (2) are in place.

Crankcase Sealant:

PN 2871557

3.

Assemble MAG crankcase to PTO crankcase
immediately. Do not allow sealant to dry.

4.

Tap crankcase evenly until fully seated with a soft
sided hammer.

5.

Install the

new

crankcase bolts finger tight in MAG

side crankcase.

6.

Tighten all bolts evenly until snug.

ENGINE

«
...
141
142
143
144
145
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: Bajaj Motorsport Страницы: 8

Бренд: Landoll Страницы: 64

Бренд: Polaris Страницы: 215

Бренд: E-TON Страницы: 30

Бренд: Cushman Страницы: 158

Бренд: Lil Pick Up Страницы: 29

Бренд: Ski-Doo Страницы: 52

Бренд: Suzuki Страницы: 139

Бренд: MINIMOTO Страницы: 33

Бренд: PAXSTER Страницы: 24

Viper Jr. (RXL-40)

Бренд: E-TON Страницы: 23

Бренд: E-Z-GO Страницы: 135

Бренд: Camoplast Страницы: 55

Бренд: Yamaha Страницы: 94

Бренд: Bennche Страницы: 181

Бренд: Herculano Страницы: 34

Бренд: Baja motorsports Страницы: 82

Бренд: Toro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды