Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 281

Страница: 281 / 456

6.47

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Troubleshooting, Continued.....

SITUATION

PROBABLE CAUSE

REMEDY

PVT cover
overheating
(melting)

-Plugged air intake or outlet.

-Belt slippage due to water, oil, grease, etc.,
rubbing on cover.
-Clutches or weight being applied to cover
while in operation.

-High vs. low range.

-Clear obstruction

-Inspect system. Clean , repair or replace as
necessary.
Seal PVT system ducts.-Remove weight. Inform
operator.

-Instruct operator on guidelines for operation in
proper driving range for different terrain as
outlined in Owner’s Safety and Maintenance
Manual.

Water ingestion

-Cover seals or ducts leaking

-Operator error

-Find leak and repair as necessary.

-Instruct operator on guidelines for operation in
wet terrain as outlined in Owner’s Safety and
Maintenance Manual.

Belt slippage

-Belt worn out

-Water ingestion

-Belt contaminated with oil or grease

-Replace belt.

-Inspect and seal PVT system.

-Inspect and clean.

PVT noise

-Belt worn or separated, thin spots, loose belt
-Broken or worn clutch components, cover
hitting clutches

-Replace belt.
-Inspect and repair as necessary.

Engagement
erratic or stabby

-Thin spots on belt, worn belt
-Drive clutch bushings stick

-Replace belt. Refer to belt burnt troubleshooting
and instruct operator.
-Inspect and repair clutches.

CLUTCHING

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды