Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 233

Страница: 233 / 456

5.39

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Front Strut Cartridge Replacement

NOTE: Refer to illustration on following page.

Hold strut rod and remove top nut.

Remove upper strut pivot assembly.

Strut Rod Wrench:

(PN 2871572)

Strut Spring Compressor Tools:

(PN 2871573) and (PN 2871574)

Compress spring using any commercially available
spring compressor tool and remove the spacer nut.

Remove coil spring and collapse strut cartridge.

Remove two pinch bolts from strut casting.

Remove strut cartridge.

Install cartridge until bottomed in strut casting.

Install pinch bolts with wire clamp (s). Torque pinch
bolts to specification.

Pinch Bolt:

17 ft-lbs (23 Nm)

Reassemble spring and top pivot assembly. Be sure
all parts are installed properly and seated fully.

10. Torque strut rod nut to specification. Do not over

torque the nut.

Strut Rod Nut:

15 ft-lbs (21 Nm)

BODY / STEERING / SUSPENSION

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды