Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 456

background image

4.14

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

Fuel Pump Test

If a fuel delivery problem is suspected, make certain the
fuel pump filters are not plugged, that the pump is being
activated through the ECU, all electrical connections are
properly secured, the fuses are good, and a minimum of
7.0 volts is being supplied. If during starting the battery
voltage drops below 7.0 volts, the ECU will fail to operate
the system.

WARNING

Fuel is extremely flammable and may cause severe

burns, injury, or death.

Do not use any device that produces a flame or

electrical devices that may spark around

fuel or fuel vapors.

1.

Remove the front cab.

2.

Cover the fuel line connection at the fuel tank with a
shop towel and disconnect the line from the fuel
pump outlet.

3.

Install the Fuel Pressure Gauge Adaptor (PV-48656)
in-line between the fuel pump outlet and fuel line.

4.

Connect the hose from the Fuel Pressure Gauge Kit
(PU-43506-A) to the test valve on the Fuel Pressure
Gauge Adaptor (PV-48656). Route the clear hose
into a portable gasoline container or the vehicle’s
fuel tank.

5.

Turn on the key switch to activate the pump and
check the system pressure on the gauge. If system
pressure of 58 ± 2 psi (400 ± 14 kPa) is observed,
the ignition switch, ECU, fuel pump, and pressure
regulator are working properly. Turn the key switch
off and depress the valve button on the tester to
relieve the system pressure.

Normal Fuel Pressure:

58 ± 2 psi (400 ± 14 kPa)

NOTE: If the fuel pressure is out of specification,
replace the fuel pump assembly.

6.

If the pump did not activate (Step 5), disconnect the
harness connector from the fuel pump. Connect a
DC voltmeter across terminals “3” and “4” in the plug
on the vehicle fuel pump harness. Turn on the key
switch and observe voltage to ensure a minimum of
7 volts is present.

NOTE: If the voltage was below 7 VDC, test the
battery, ignition switch, relay (s), wiring harness
and ECU.

7.

If the reading is between 7 and 14 volts, turn key
switch off and connect an ohmmeter between
terminals “3” and “4”' at the white fuel pump
connector to check for continuity within the fuel
pump.

NOTE: If there was no continuity between the
pump terminals, replace the fuel pump assembly.

FUEL SYSTEM - GENERAL

«
...
158
159
160
161
162
...
»

Содержание 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 Sportsman 570 EF

Бренд: KAYO MOTO Страницы: 9

ATV8E - SERVICE

Бренд: Eton Страницы: 34

Бренд: Toro Страницы: 28

Wagon with tilt

Бренд: Texas Страницы: 42

MAVERICK X3 Series 2017

Бренд: Can-Am Страницы: 155

Transit Bench 900

Бренд: STARKE ARVID Страницы: 5

Бренд: gio Страницы: 22

Бренд: Arctic Cat Страницы: 70

Бренд: Arctic Cat Страницы: 101

Бренд: PRONAR Страницы: 147

Бренд: E-Z-GO Страницы: 192

Бренд: Jayco Страницы: 104

Бренд: Baja Страницы: 82

Бренд: Jayco Страницы: 93

Бренд: Moni Страницы: 16

Бренд: jcb Страницы: 227

Бренд: Yamaha Страницы: 154

Rhino 450 YXR45FAV

Бренд: Yamaha Страницы: 413

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды