Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 87

Страница: 87 / 456

3.29

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

19. Install the water pump cover to the stator cover.

Torque all fasteners in sequence to specification.

Stator Cover and Water Pump Cover:

9 ft-lbs (12 Nm)

20. Install the oil dipstick.

21. Install the coolant hose to the water pump cover and

tighten hose clamp.

22. Connect the stator wire connector and securing the

wiring to the front engine mount bracket.

23. Install the CPS sensor into the stator cover. Inspect

CPS O-ring and replace if needed.

24. Install the seat, right side panel and footwell.

25. Connect the (-) negative battery cable.

26. If the engine oil was contaminated during this service

procedure, perform an engine oil change as outlined
in Chapter 2. DO NOT run the engine until coolant
has been added to the cooling system.

27. Fill cooling system with recommend coolant and

bleed the system of air as outlined in this chapter.

28. Check for leaks.

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды