Perkins New 1000 Series Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 290

Perkins New 1000 Series Скачать руководство пользователя страница 93

Workshop Manual, TPD 1350, issue 3

93

14

New 1000 Series

8 Fit the setscrews to the main bearing caps and
tighten them gradually and evenly to 265 Nm (196
lbf ft) 27,0 kgf m.

9 Clean the bridge piece and the location areas for
the bridge piece in the cylinder block. Use a straight
edge (A2) to ensure that the bridge piece is in line with
the rear face of the cylinder block. Tighten the bridge
piece cap screws (A1) to 16 Nm (12 lbf ft) 1,6 kgf m.

10 When the bridge piece is in position, inject
POWERPART silicone adhesive or POWERPART
silicone rubber into the groove (B2) at each end of the
bridge piece. Continue to inject sealant until the
groove is completely full and the sealant leaves the
lower groove (B1) at the front and rear of the bridge
piece.

It may be necessary to stop the sealant at one side of
the lower groove in order to ensure it will flow from the
opposite side of the groove.

Caution: When the sump joint is removed, damage
can occur to the seal in the grooves of the bridge
piece. If the seal is damaged, apply enough sealant to
completely fill the grooves.

Note: Most of the latest engines have setscrews in
place of studs to fasten the sump to the bridge piece.
The threads of the setscrews have a sealant applied
by the manufacturer. When the setscrews are to be
used again, ensure that the threads of the setscrews
and of the bridge piece are clean and a sealant is
applied to the threads of the setscrews. These
instructions also apply to studs.

11 Fit the connecting rod caps,

see operation 13-1

.

Rotate the crankshaft two turns to ensure free
movement.

12 On four cylinder engines, if necessary, fit the
balancer unit

, see operation 14-12

. If a balancer unit

is not used, fit the lubricating oil pump, the lubricating
oil suction pipe and strainer, the delivery pipe and the
relief valve (four cylinder engines) and if necessary,
the lubricating oil crossover pipe,

see section 19

.

13 Fit the rear oil seal housing

, see operation 14-4

.

14 Fit the flywheel housing and the flywheel,

see

section 22.

15 Fit the timing case and the timing gears,

see

section 15.

16 Fit the timing case cover,

see operation 15-1.

17 Fit the compressor and its drive assembly or fit the
exhauster,

see section 24.

18 Fit the alternator and its mounting bracket,

see

section 23.

19 Fit the crankshaft pulley

, see operation 14-1

or

operation 14-2

.

20 Fit the fuel injection pump,

see section 20

.

21 Fit the coolant pump, the fan drive pulley and
housing, the drive belts and the fan,

see section 21

.

22 Fit the lubricating oil sump,

see operation 19-3.

23 After the engine has been installed, fill the
lubricating oil sump to the correct level with an
approved oil. Fill the cooling system.

1

2

A

A0109

1

2

B

A0110

Purchased from www.WorkshopManuals.co.uk

«
...
91
92
93
94
95
...
»

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов