manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 37 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 37

Workshop Manual, TPD 1350, issue 3

37

 

12

New 1000 Series

Valve springs

To change the valve springs
(with cylinder head fitted)

12-6

Special tools

Valve spring compressor, PD.6118B

Stud adaptor used with PD.6118B, PD.6118-7

Setscrew adaptor used with PD.6118B, PD.6118-8

Note: Paragraphs 1 to 12 refer to a change of valve 
springs for a single cylinder.

Warning! Wear eye protection during this operation.

1  Remove the rocker cover

, see operation 12-1

.

2  Rotate the crankshaft in the normal direction of 
rotation until the inlet valve of the relevant cylinder 
has just opened and the exhaust valve has not fully 
closed. In this position the piston will be at 
approximately top dead centre (TDC).

3  Remove the rocker assembly

, see operation 12-2

.

4  Fit the valve spring compressor (A1) and the 
relevant adaptor (A2 or A3).

5  Compress the valve spring and remove the collets. 
Ensure that the valve spring is compressed squarely 
or damage to the valve stem can occur.

Caution: Do not rotate the crankshaft while the valve 
springs are removed.

6  Release the valve spring compressor and remove 
the valve spring caps and valve spring.

Caution: The outer diameter of the exhaust valve 
guide is 1 mm larger than the inlet valve guide. To 
prevent leakage past the inlet valve stem it is 
important that the larger exhaust valve seal is not 
fitted onto the inlet guide. The seals have a colour 
code for identification.

7  Fit new valve stem seals on the valve guides. 
ensure that the brown seal is fitted to the exhaust 
valve and green seal is fitted to the inlet valves. 

8  Put the new valve springs in position.

Continued

1

3

2

A

A0051

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов