manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 231 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 231

Workshop Manual, TPD 1350, issue 3

231

 

21

New 1000 Series

5  A tool (A) can be made to press the coolant seal 
into position. The tool should be made of a suitable 
material to the dimensions listed below:

A 44,0 mm (1.73 in)

B 40,0 mm (1.57 in)

C 11,6 mm (0.46 in)

D 35,8 mm (1.41 in)

E 16,1 mm (0.63 in)

F 1,00 mm (0.04 in) at 45°

G 2,00 mm (0.08 in) at 45° 

The dimensions of the tool to fit the coolant seal, will 
ensure that the seal is the correct length after it is 
installed. It will also prevent axial distortion of the seal 
when it is pressed onto the shaft.

6  Turn the pump over and support the drive end of the 
body. Do not lubricate the coolant seal (B4). It is 
important that the seal is not contaminated by oil or 
grease and if it is held in the hand, it should be held 
by the edge of the flange. Do not damage the ring of 
green sealant applied to the body of the coolant seal 
just behind the flange. Put the seal into position on the 
end of the shaft. Ensure that the ring of sealant is 
towards the bearing. Use the tool to press the seal 
onto the shaft until the bottom of the seal flange is in 
complete contact with the pump body.

7  Hold the pump with the drive end of the shaft on a 
suitable support. With the use of a suitable distance 
piece and a flat bar, press the new impeller (B3) onto 
the shaft until the front face of the impeller is 6,7/7,0 
mm (0.26/0.28 in) below the front face of the pump 
body (B1). Remove the flat bar and distance piece 
and ensure that the shaft is free to rotate.

8  Clean the threads in the front face of the pump 
body. Fit a new joint (B6) and the cover (B5). Fit the 
setscrews and tighten them to 9 Nm (6 lbf ft) 0,9 kgf 
m. If the setscrews are new, a sealant will have been 
applied to the threads by the manufacturer. If the 
original setscrews are to be used again, the threads 
should be cleaned and a POWERPART Nutlock 
applied.

9  Fit a new "O" ring (B2) to the body of the pump.

A

C

F

D

E

G

B

A

A0188

1

6

5

4

3

B

A0270

2

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов