Perkins New 1000 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 290

Perkins New 1000 Series Скачать руководство пользователя страница 44

12

44

Workshop Manual, TPD 1350, issue 3

New 1000 Series

20 For engines fitted with turbochargers: Fit the
turbocharger

, see operation 18-1

.

21 Fit the fuel pipe between the fuel filter and the fuel
lift pump.

22 Fit the fuel pipe between the fuel filter and the
fuelled starting aid in the induction manifold. Connect
the electrical connection to the cold start device.

23 For engines fitted with a boost control device: Fit
the boost control pipe between the induction manifold
and the top of the fuel injection pump.

24 Fit the electrical connection to the coolant
temperature sender unit.

25 Connect the coolant outlet and the hoses for the
cab heater. Tighten the clips.

26 Fill the cooling system.

27 Connect the air filter/cleaner.

28 Connect the battery.

29 Eliminate air from the fuel system,

, see operation

20-9

.

30 Start the engine and run it at low speed. Check
that oil flows from the holes in the rocker levers. If the
oil flow is correct, fit the rocker cover

, see operation

12-1

.

Note: It is not necessary to tighten the cylinder head
setscrews again with the engine hot or after a limited
period in service.

Purchased from www.WorkshopManuals.co.uk

«
...
42
43
44
45
46
...
»

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов