manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 50 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 50

12 

50

Workshop Manual, TPD 1350, issue 3

New 1000 Series

To inspect and to correct

12-9

Special tools:

Gauge, valve depth, PD.41D

Dial gauge for use with PD.41D, PD.208

1  Check the depth of the valves below the face of the 
cylinder head before the valve springs are removed.

2  Ensure that the heads of the valves and the bottom 
face of the cylinder head are clean. 

3  Put the valve depth gauge on the face of the 
cylinder head and zero the dial gauge. 

4  Carefully put the valve depth gauge in position over 
the head of each valve (A) and make a note of the 
measurement. The maximum depth, in service, is 
given in the data and dimensions. 

5  If a valve is below the depth limit, check the valve 
depth with a new valve in position. If the valve depth 
is still below the limit and a valve seat insert is fitted, 
the insert must be renewed. 

6  Check the valves for cracks. Check the stems of the 
valves for wear and for correct fit in their valve guides.

Caution: Renew damaged valves, the special heat 
resistant layer on the face of the valve will be detroyed 
if valves are lapped.

7  Check that the seat faces of the valves are not 
badly burnt or damaged. Seat faces of valves which 
are damaged can be ground on a special machine. 
When new valves are fitted, the valve depths must be 
checked after the valve springs are fitted.

8  Check that the load on the valve springs is correct 
at their fitted length, see the data and dimensions. Fit 
new valve springs at every complete engine overhaul.

A

A0063

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов