manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 262 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 262

23 

262

Workshop Manual, TPD 1350, issue 3

New 1000 Series

Drive belts

To check

23-1

1  Check the belt(s) for wear and damage and renew 
the belt(s), if necessary. If twin belts are fitted, they 
should both be renewed.

2  Check the belt tension. If twin belts are fitted, 
check/adjust the tension on the tighter belt. To ensure 
maximum belt life, it is recommended that a belt 
tension gauge is used. Fit the gauge (A1) at the 
centre of the longest free length and check the 
tension. If a Burroughs gauge is used, the correct 
tension is 355 N (80 lbf) 36 kgf. If the tension is equal 
to or less than 220 N (50 lbf) 22 kgf, adjust it to 355 N 
(80 lbf) 36 kgf

, see operation 23-2

. If no gauge is 

available, press down the belt with the thumb at the 
centre of the longest free length and check the 
deflection (B). With moderate thumb pressure, 45 N 
(10 lbf) 4,5 kgf, the correct belt deflection is 10 mm (3/
8 in).

To adjust tension

23-2

1  Loosen the pivot fasteners (B1) of the alternator 
and the fasteners of the adjustment link (B2).

2  Change the position of the alternator to give the 
correct tension. Tighten the adjustment link fasteners 
and then the pivot link fasteners. If there are two pivot 
fasteners, tighten the front fastener and then the rear 
fastener.

3  Check the belt tension again to ensure that it is still 
correct.

To remove and to fit

23-3

Where twin belts are fitted, they are supplied as a set 
and must be renewed as a set.

1  Loosen the pivot fasteners (B1) of the alternator 
and the adjustment link fasteners (B2).

2  Release all of the tension from the belt(s) and 
remove the belt(s).

3  Fit the new belt(s) and adjust the tension

, see 

operation 23-2

. The belt tension must be checked 

again after the first 1000 km (600 miles) or 20 hours 
of operation.

1

A

A0281

B

A0282A

1

2

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов