manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 205 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 205

Workshop Manual, TPD 1350, issue 3

205

 

20

New 1000 Series

To fit

Cautions:

!

The engine must be set to TDC number 1 cylinder, 
compression stroke before the pump is fitted. If the 
crankshaft needs to be rotated, the pump must be 
fitted temporarily, or the loose gear could damage 
the timing case.

!

The drive shaft of the pump must not be rotated 
without the spacer (A1) in position under the 
locking screw (A2). If the drive shaft is rotated with 
the locking screw tightened on to the shaft, the 
drive shaft will be damaged.

1  Inspect the "O" ring (B1) in the pump flange and, if 
necessary, fit a new "O" ring. 

2  Lightly lubricate the "O" ring with clean engine 
lubricating oil and put the pump into position on the 
timing case.

3  Put the fuel pump in position on the three studs and 
fit the flange nuts.

4  Fit the setscrew and nut of the support bracket. 
Ensure that force is not applied to the fuel pump when 
the support bracket is fitted.

5  Tighten the flange nuts of the fuel pump to 28 Nm 
(20 lbf ft) 2,8 kgf m.

Caution: Do not remove the nut (C2) from the shaft 
of the fuel injection pump. The fuel pump hub is fitted 
to the shaft in the factory to ensure that the fuel pump 
is in the correct position for timing. If the hub is 
removed, the hub will need to be accurately fitted to 
the pump by use of special equipment available to 
Perkins distributors.

6  Put the fuel pump gear onto the hub of the fuel 
pump. The fasteners (C6) for the fuel pump gear 
should be in the centre of the slots to allow for the 
removal of the backlash. Tighten the setscrews finger 
tight.

Note: The fuel pump gear will only fit in one position. 
The gear is fitted with the letters C and M at the front.

7  Insert the timing pin (C1) through the hole (C5) of 
the fuel pump gear and the slot of the hub (C4) until it 
can be pushed fully into the hole (C3) in the body of 
the fuel pump. If the timing pin cannot be pushed into 
the pump body, check that the engine is correctly set 
at TDC on the number 1 cylinder, 

see operation 17-1

 

or , 

see operation 17-2

.

Continued

3

2

1

B

A0299

C 0 07 3/1

1

2

A

3

4

1

5

6

2

A 03 74

C

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов