manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 111 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 111

Workshop Manual, TPD 1350, issue 3

111

 

15

New 1000 Series

Front oil seal

To remove and to fit

15-2

Special tools:

Replacer tool for front oil seal (main tool), PD170

Pressure plate for use with PD.170, PD.170-1

Sleeve for use with PD.170, PD.170-2

Fastener plate for use with PD.170, PD.170-3 

Adaptor for use with PD.170

 (1)

(1) Refer to your nearest Perkins distributor.

To remove

1  Remove the fan, 

see operation 21-9

. and the drive 

belts, 

see operation 23-3

.

2  Remove the crankshaft pulley, 

see operation 14-1

 

or 

operation 14-2

.

3  Remove the oil seal with a suitable lever behind the 
main lip of the oil seal. Do not damage the edge of the 
oil seal housing.

To fit

Note: The seal is fitted to a depth of 10,20/10,70 mm 
(0.402/0.421 in) from the front face of the oil seal 
housing to the flat front face of the oil seal. If, in 
service, there is wear in the seal location area of the 
crankshaft pulley, oil will continue to leak after a new 
oil seal is fitted. To renew a worn crankshaft pulley

, 

see operation 15-3

.

1  Clean the oil seal housing. Inspect the new seal for 
damage. If a scratch can be seen across the lip of the 
seal, do not fit the seal.

2  Lubricate the outer circumference of the oil seal 
with clean engine lubricating oil and enter the seal into 
the housing. Ensure that the spring loaded lip of the 
oil seal is towards the inside of the timing case cover 
and that the oil seal is square to the bore of the seal 
housing.

3  Assemble the oil seal replacer tool (A). Fit the 
fastener plate, PD.170-3, (A3) to the front of the 
crankshaft. Put the adaptor, (A5) on the nose of the 
crankshaft and against the seal. Ensure that the 
adaptor has the side stamped 10,5 mm towards the 
seal.

Assemble the pressure plate, PD.170-1, (A2) 
together with the sleeve, PD.170-2, (A4) onto the 
threaded bar, PD.170, (A1). Put the tool assembly in 
position on the adaptor, and tighten the threaded bar 
onto the stud of PD.170-3 (A3).

Fit a rod through the hole in the end of the threaded 
bar to prevent movement of the bar when the nut is 
tightened. Tighten the nut to push the seal into the 
housing to the correct depth.

4  Remove the replacer tool and lightly lubricate the 
seal location area of the crankshaft pulley with clean 
engine lubricating oil. Fit the crankshaft pulley, 

see 

operation 14-1

 or 

operation 14-2.

5  Fit the drive belts, 

see operation 23-3

 and adjust 

the belt tension, 

see operation 23-2.

6  Fit the fan, 

see operation 21-12

.

5

4

3

2

1

A

A 0 12 7

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов