manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 215 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 215

Workshop Manual, TPD 1350, issue 3

215

 

20

New 1000 Series

To eliminate air from the fuel system 20-15

If air enters the fuel system, it must be removed 
before the engine can be started.

Air can enter the system if:

!

The fuel tank is drained during normal operation.

!

The low-pressure fuel pipes are disconnected.

!

A part of the low-pressure fuel system leaks during 
engine operation.

In order to eliminate air from the fuel system, proceed 
as follows:

Vent screws are not fitted to the fuel injection pump. 
Air will usually be removed from the fuel pump 
automatically.

Caution: If the fuel system is empty or if the 
canister(s) of the fuel filter have been renewed, it will 
be necessary to eliminate air from the fuel system, 
especially the fuel injection pump.

1  Loosen the vent plug on the filter head of the pre-
filter (A2). Operate the priming lever of the fuel lift 
pump (B) until fuel, free of air, comes from the vent 
plug. Tighten the vent plug.

Note: If the drive cam of the fuel lift pump is at the 
point of maximum lift, it will not be possible to operate 
the priming lever. In this situation, the crankshaft must 
be rotated one revolution.

2  Loosen the vent plug (A1) on the top of the filter 
head. Operate the priming lever of the fuel lift pump 
until fuel, free of air, comes from the vent plug. 
Tighten the vent plug.

Continued

B

L0012A

2

1

A

A0368

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов