Perkins New 1000 Series Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 290

Perkins New 1000 Series Скачать руководство пользователя страница 137

Workshop Manual, TPD 1350, issue 3

137

16

New 1000 Series

Data and dimensions

Note: This information is given as a guide for personnel engaged on engine overhauls. The dimensions which
are shown are those which are mainly used in the factory. The information applies to all engines, unless an
engine type code is shown.

Cylinder block assembly

Cylinder block

Height between top and bottom faces . . . . . . . . . . . . . . . . . . . . . . . . . . 441,12/441,33 mm (17.367/17.375 in)

Diameter of parent bore for cylinder liner . . . . . . . . . . . . . . . . . . . . . . . . . 104,20/104,23 mm (4.103/4.104 in)

Depth of recess for flange of cylinder liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,81/3,91 mm (0.150/0.154 in)

Diameter of recess for flange of cylinder liner . . . . . . . . . . . . . . . . . . . . . . 107,82/107,95 mm (4.245/4.250 in)

Diameter of cylinder bore, engine types AR and AS only . . . . . . . . . 103,000/103,025 mm (4.0551/4.0561 in)

Maximum permissible bore wear, engine types AR and AS only . . . . . . . . . . . . . . . . . . . 0,15 mm ( 0.006 in)

Diameter of first oversize cylinder bore,

engine types AR and AS only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103,500/103,525 mm (4.0748/4.0757 in)

Diameter of second oversize cylinder bore,

engine types AR and AS only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104,000/104,025 mm (4.0944/4.0954 in)

Diameter of parent bore for main bearing . . . . . . . . . . . . . . . . . . . . . . . 80,416/80,442 mm (3.1660/3.1670 in)

Camshaft bore diameter

- Four cylinder engines:

Number 1 (for bush) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55,56/55,59 mm (2.188/2.189 in)

Number 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,55/50,60 mm (1.990/1.992 in)

Number 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,04/50,09 mm (1.970/1.972 in)

- Six cylinder engines:

Number 1 (for bush) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55,56/55,59 mm (2.188/2.189 in)

Number 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,55/50,60 mm (1.990/1.992 in)

Number 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,29/50,34 mm (1.980.1.982 in)

Number 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,04/50,09 mm (1.970/1.972 in)

Bore of bush for number 1 camshaft journal . . . . . . . . . . . . . . . . . . . . . . . . . 50,79/50,85 mm (2.000/2.002 in)

Cylinder liners

Type:

- Production . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dry, interference fit, flanged, with flame ring

- Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry, transition fit, flanged, with flame ring

- Partially finished liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry, interference fit, flanged, with flame ring

Outside diameter of production liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104,25/104,28 mm (4.105/4.106 in)

Interference fit of production liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,03/0,08 mm (0.001/0.003 in)

Inside diameter of production liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100,00/100,03 mm (3.937/3.938 in)

Transition fit of service liner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 0,03 mm (+/- 0.001 in)

Inside diameter of service liner with a flame ring (fitted) . . . . . . . . . . . . . 100,00/100,063 mm (3.937/3.939 in)

Maximum permissible wear of liner bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,25 mm (0.010 in)

Thickness of flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,81/3,86 mm (0.150/0.152 in)

Relative position of top of liner flange to top face of cylinder block . . . . . . . . . . . . . 0,10 mm (0.004 in) above

0,10 mm (0.004 in) below

Purchased from www.WorkshopManuals.co.uk

«
...
135
136
137
138
139
...
»

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов