manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 245 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 245

Workshop Manual, TPD 1350, issue 3

245

 

21

New 1000 Series

To remove and to fit - canister type

21-14

To remove

1  Drain the cooling system.

2  Release the hose clips of the coolant pipes at the 
oil cooler (A3). Release the threaded adaptor (A5) 
from the lubricating oil cooler and pull the oil cooler 
(A6) from the hose connections and the filter head 
(A1).

To fit

1  Clean the joint face of the filter head (A2).

2  Check the washer (A4) and the seals (A7 and A8) 
for damage. Renew the washer and the seals if they 
are damaged or worn. Lightly lubricate the seals with 
clean lubricating oil.

3  Push the hose connections for the coolant pipes 
onto the lubricating oil cooler. Hold the oil cooler in 
position against the filter head and fit the threaded 
adaptor. Tighten the threaded adaptor to 37 Nm (27 
lbf ft) 3,8 kgf m. Ensure that the hose connections are 
fitted correctly and tighten the hose clips.

4  Fill the cooling system.

4

1

8

3

2

7

6

5

A

L0027

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов