manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 195 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 195

Workshop Manual, TPD 1350, issue 3

195

 

20

New 1000 Series

5  Put the diaphragm assembly in position over the 
lower half of the body with the blade of the pull rod 
aligned with the slot in the link arm. Press lightly down 
on the diaphragm until the notch in the pull rod is in 
the slot in the link arm and turn the diaphragm 90° in 
either direction. This action will engage and retain the 
pull rod in the slot of the link arm.

6  Push the rocker arm towards the pump body until 
the diaphragm is level with the body flange and fit the 
top half of the body in position with the marks on the 
flanges aligned. Keep the pressure on the rocker arm; 
fit the spring washers and the screws and tighten 
them evenly.

7  Fit the gauze filter (A2) and the cover (A1), ensure 
that the rubber seal (A13) is fitted correctly and 
tighten the screw.

To test

20-6

1  Disconnect the fuel outlet pipe from the fuel lift 
pump. Fit a 0-70 kPa (0-10 lbf/in

2

) 0-0,7 kgf/cm

2 

pressure gauge to the outlet of the lift pump. Release 
the connection at the gauge and operate the priming 
lever of the lift pump to eliminate air from the pipe. 
When fuel, free of air, flows from the pipe tighten the 
connection. Ensure that there are no leaks at the 
connections between the pump and the gauge.

2  Operate the starter motor for 10 seconds with the 
engine stop control in the stop position or with the 
stop solenoid disconnected.

3  Note the maximum pressure indicated on the 
gauge. If the pressure indicated is less than the test 
pressure shown in the data and dimensions, repair or 
renew the pump. Also check the rate at which the 
pressure reduces to half the maximum pressure 
obtained. If this is less than 30 seconds, repair or 
renew the pump.

4  Remove the gauge and connect the outlet pipe to 
the lift pump. Release the vent screw on the fuel filter 
head and operate the priming lever until fuel, free of 
air, flows from the vent screw. Tighten the vent screw.

5  Connect the engine stop solenoid.

A

A0252

2

3

4

5

6

7

8

9

1

3

12

11

10

4

13

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов