manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 203 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 203

Workshop Manual, TPD 1350, issue 3

203

 

20

New 1000 Series

Lucas DP 200 Series fuel injection pump

To remove to fit

20-10

Special tools:

Timing pin PD.246, Lucas fuel injection pumps

General description

Caution: Do not release the nut (C2) from the fuel 
injection pump. Illustration (C) shows the nut in 
position when the fuel pump is fitted to the engine. 
The fuel pump hub is fitted to the shaft in the factory 
to ensure that the fuel pump is in the correct position 
for timing. If the nut is removed and the hub moves, 
the hub will need to be accurately fitted to the pump 
by use of specialist equipment before the pump can 
be fitted to the engine.

The manufacturer fits the hub (A2) to the pump to 
ensure very accurate timing. Engines that have this 
arrangement have the drive gear fastened to the hub 
instead of to the shaft of the pump.

The hub is permanently mounted onto the drive shaft 
by the pump manufacturer to allow the pump timing to 
be set accurately when the engine is in service.

To prevent incorrect adjustments to the engine timing 
by rotation of the fuel pump, the mounting flange (B1) 
has holes instead of slots.

Accurate timing of the pump to the engine is by a pin 
(C1) used to align the fuel pump gear and the the hub 
(C4), with a hole in the body (C3) of the fuel pump. 
The gear is passed over the pin and fastened to the 
hub with four fasteners (C6).

Note: On the latest engines with belt driven coolant 
pumps, four tamper proof fasteners retain the fuel 
pump gear. Special tools to remove these fasteners 
are available at your Perkins distributor.

Caution: A new fuel injection pump may be supplied 
with the pump shaft in the locked position. The drive 
shaft of the pump must not be turned without the 
spacer (B2) in position under the locking screw (B3).

The fuel injection pump has a locking screw (A3) and 
(B3) and a spacer (B2). The locking screw prevents 
the rotation of the drive shaft.

An "O" ring (A1) is fitted into a groove in the pump 
flange. This "O" ring is fitted instead of a joint between 
the pump flange and the timing case.

3

2

1

A

A0299

3

4

1

5

6

2

A 03 74

C

C 00 73 /2

2

1

3

B

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов