manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 265 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 265

Workshop Manual, TPD 1350, issue 3

265

 

23

New 1000 Series

If the warning light is not illuminated when the 
switch is in the "on" position:

Check the bulb. If no fault:

Check all the connections at the regulator, at the 
alternator and at the battery.

If no fault:

Turn the switch to the "off" position. Disconnect the 
wire from the "F" terminal on the alternator and 
connect a wire between the "F" terminal and the 
negative terminal on the alternator. Turn the switch to 
the "on" position.

If the warning light shows, the fault is in the regulator.

If the warning light does not show, the fault is in the 
alternator.

If the warning light continues to show and the 
ammeter shows no output when the alternator is 
in operation:

Check all the connections at the regulator, alternator 
and battery.

If no fault:

Turn the switch to the "off" position. Disconnect the 
wire from the "F" terminal on the alternator and 
connect a wire between the "F" terminal and the 
negative terminal on the alternator. Turn the switch to 
the "on" position and operate the engine at fast idle.

If there is no output, there is a fault in the alternator.

If there is an output, there is a fault in the regulator.

If the warning light continues to show when the 
alternator is in operation and the ammeter shows 
a reduced output with maximum output only at 
maximum engine speed or,if the warning light 
does not show, but there is a reduced output from 
the alternator with maximum output only at 
maximum engine speed:

There is a fault in the alternator.

If there is an intermittent light from the warning 
light and the ammeter needle is not stationary 
when the battery is charged fully and no load is 
applied:

Check for a higher than normal resistance in the 
negative control wire of the regulator.

If the resistance is normal, there is a fault in the 
regulator.

If the battery charge is too high and the ammeter 
indicates high or maximum output at all times:

Check the positive control wire and its connection at 
the regulator.

If the wire and its connection are correct, there is a 
fault in the regulator.

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов