manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 118 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 118

15 

118

Workshop Manual, TPD 1350, issue 3

New 1000 Series

Fuel pump gear

The fuel injection timing is set with specialist tools in 
the factory after the engine has been accurately set to 
TDC, number 1 cylinder on the compression stroke. 
The fuel pump gear has timing marks (A) which can 
be used to find the approximate position of TDC on 
number 1 cylinder compression stroke. The marked 
teeth of the crankshaft, the camshaft and the fuel 
pump gears will be in mesh with the idler gear when 
number 1 piston is close to top dead centre (TDC) on 
the compression stroke. The marked teeth of the idler 
gear may not necessarily be in mesh in this position, 
because of the different speeds at which the gears 
rotate.

The fuel injection pump is timed at TDC on the 
compression stroke of number 1 cylinder. It is 
important that fuel injection timing is accurate to 
conform to emissions legislation. Always use 

operation 17-1

 or 

operation 17-2

 to obtain TDC on the 

compression stroke of number 1 cylinder accurately.

To remove and to fit

15-6

To remove

Special tools:

Bosch fuel injection pump timing pin, PD.245 

Stanadyne and Lucas fuel injection pump timing pin, 
PD.246

1  Remove the timing case cover

, see operation 15-1

.

Caution: Do not lock the shaft of the fuel injection 
pump, 

see operation 20-7

 or 

operation 20-10

.

2  Set the number one piston to TDC on the 
compression stroke, 

see operation 17-1

 or 

operation 

17-2.

Fit the timing pin (B3) until the small end of the pin 
(B2) is pushed fully into the hole in the fuel pump body 
(B4). The pin can only be fitted when the number one 
piston is correctly in position at TDC on the 
compression stroke. If the timing pin cannot be 
pushed into the pump body, check the timing of the 
fuel injection pump, 

see operation 17-3

.

Caution: Do not remove the nut (B5) which retains 
the hub (B1) to the shaft of the fuel injection pump. 
The hub is fitted permanently to the shaft. If the hub is 
moved, it will be necessary for a fuel injection pump 
specialist to correctly position the hub on the shaft 
with special test equipment.

3  Remove the four fasteners (A1) from the fuel pump 
gear and remove the gear from the hub of the fuel 
pump.

Note: On the latest engines with belt driven coolant 
pumps, four tamper proof fasteners retain the fuel 
pump gear. Special tools are needed to remove these 
fasteners, refer to your Perkins distributor.

4  Inspect the gear for wear and other damage and 
renew it, if necessary.

A

A0129

1

5

1

4

3

2

B

A 0 37 2/1

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов