manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 49 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 49

Workshop Manual, TPD 1350, issue 3

49

 

12

New 1000 Series

Valves and valve springs

To remove and to fit

12-8

Special tools:

Valve spring compressor, PD.6118B

Stud adaptor, PD.6118-7

Setscrew adaptor, PD.6118-8

To remove

Warning! Wear eye protection during this operation.

1  Remove the cylinder head

, see operation 12-7

.

2  Clean the bottom face of the cylinder head and 
check the depth of the heads of the valves below the 
face of the cylinder head

, see operation 12-9

.

3  Make a suitable mark on the heads of the valves to 
ensure that the valves can be fitted in their original 
positions, if they are to be used again.

Caution: Ensure that the valve springs are 
compressed squarely or the valve stem can be 
damaged.

4  Use the valve spring compressor and the relevant 
adaptor to compress the valve spring (A3) and 
remove the collets (A2).

5  Release the valve spring compressor and remove 
the valve spring cap (A1), valve spring and valve stem 
seal (A4).

6  Repeat items 4 and 5 for the other valves.

To fit

Warning! Wear eye protection during this operation.

Note: The components of the valve assembly are 
shown in A.

1  Lubricate the valve stem (A5) with clean engine oil 
and fit the valves in their respective guides.

Caution: The outer diameter of the exhaust valve 
guide is 1 mm larger than the inlet valve guide. To 
prevent leakage past the inlet valve stem it is 
important that the larger exhaust valve seal is not 
fitted onto the inlet guide. The seals in the service kit 
have different colours for identification.

2  Fit new valve stem seals on the valve guides. 
ensure that the brown seal is fitted to the exhaust 
valve and green seal is fitted to the inlet valves. 

3  Put the valve springs in position, they can be fitted 
with either end to the cylinder head. Fit the valve 
spring cap.

Caution: Ensure that the valve spring is compressed 
squarely or damage can occur to the valve stem.

4  Use the valve spring compressor and the relevant 
adaptor to compress the valve spring and fit the 
collets.

1

2

3

4

5

A

C039

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов