Perkins New 1000 Series Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 290

Perkins New 1000 Series Скачать руководство пользователя страница 163

Workshop Manual, TPD 1350, issue 3

163

19

New 1000 Series

Filter canister

To renew

19-1

Warning! Discard the used canister (B4) and
lubricating oil in a safe place and in accordance with
local regulations.

Caution: The canister contains a valve and special
tube to ensure that lubricating oil does not drain from
the filter. Therefore, ensure that the correct Perkins
POWERPART canister is used.

The filter can have one or two canisters (B4) or (A1)
fitted. When two canisters are fitted, both must be
renewed at the same time. On some engines an oil
cooler (B2) is fitted to the filter head. This
arrangement is fitted on the left side or the right side
of the engine.

On some four and six cylinder engines the adaptor
(A2) or (B1) is sealed into the filter head. A new filter
head is supplied without the adaptor fitted; if either the
adaptor or the filter head is to be renewed, both parts
will be necessary.

1 Put a tray under the filter to contain spilt lubricating
oil.

2 Remove the filter canister with a strap wrench or a
similar tool and then discard the canister.

Note: If the adaptor is to be renewed, insert the end
of the adaptor, which has the thread sealant applied
during manufacture, into the filter head.

3 Clean the seal face of the filter head (A3).

Caution: Ensure that the adaptor (A2) or (B1) is
secure in the filter head.

4 Add clean engine lubricating oil to the new canister.
Give the oil time to fill the canister through the filter
element.

5 Lubricate the top of the canister seal (B3) with clean
engine lubricating oil.

6 Install the new canister and tighten it by hand only.
Do not use a strap wrench.

For turbocharged engines: Ensure that the engine will
not start and operate the starter motor until oil
pressure is obtained. To ensure that the engine will
not start, either put the manual stop control in the
"stop" position or disconnect the electrical stop control
of the fuel injection pump. Oil pressure is indicated
when the warning light is extinguished or by a reading
on the gauge.

7 After the lubricating oil has been added to the
sump, operate the engine and check for leakage from
the filter. When the engine has cooled, check the oil
level on the dipstick and add oil to the sump, as
necessary.

1

3

2

B

L0016

4

2

1

3

A 0 22 3/1

A

Purchased from www.WorkshopManuals.co.uk

«
...
161
162
163
164
165
...
»

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов