manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 188 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 188

20 

188

Workshop Manual, TPD 1350, issue 3

New 1000 Series

Fuel filter element

To renew

20-1

Warning! Discard the used canister and fuel oil in a 
safe place and in accordance with local regulations.

Cautions:

!

It is important that only the genuine Perkins parts 
are used. The use of a wrong canister or element 
can damage the fuel injection pump.

!

Do not allow dirt to enter the fuel system. Before a 
connection is disconnected, clean thoroughly the 
area around the connection. After a component 
has been disconnected, fit a suitable cover to all 
open connections.

Separate element type

1  Clean the outside surfaces of the fuel filter 
assembly. If a drain tap is fitted to the bottom of the 
filter bowl, drain the fuel from the filter.

2  Hold the bottom cover of the filter element and 
release the setscrew (A3) which is fitted through the 
filter head (A1) above the centre of the element.

3  Lower the bottom cover of the filter.

4  Remove the element (A4) and discard it.

5  Clean the inside surfaces of the filter head and of 
the cover.

6  Renew the seals (A2) and (A5) and lightly lubricate 
them with clean fuel.

7  Put the bottom cover under the new element and 
hold the element squarely to the filter head. Ensure 
that the element is fitted in the centre against the joint 
in the filter head. With the assembly in this position, 
engage and tighten the setscrew.

8  Eliminate the air from the fuel filter

, see operation 

20-9

, 

operation 20-12

 and 

operation 20-15

.

1

4

3

2

5

A

A0248

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов