manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 145 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 145

Workshop Manual, TPD 1350, issue 3

145

 

17

New 1000 Series

To check the timing of the fuel injection 
pump

17-4

Special tools:

Timing pin PD.245, Bosch fuel injection pumps

Timing pin PD.246, Lucas and Stanadyne fuel 
injection pumps

Caution: Do not remove the nut (A2) which retains 
the hub (A4) to the shaft of the fuel injection pump. 
The hub is fitted permanently to the shaft. If the hub is 
moved, it will be necessary for a fuel injection pump 
specialist to correctly position the hub on the shaft 
with special test equipment available to Perkins 
distributors.

1  Set the piston of number 1 cylinder to TDC on the 
compression stroke

, see operation 17-1

 or 

operation 

17-2

.

2  Remove the gear cover from the cover of the timing 
case. For gear driven coolant pumps: Remove the 
coolant pump

, see operation 21-2

.

Note: On the latest engines with belt driven coolant 
pumps, four tamper proof fasteners retain the fuel 
pump gear. Special tools and personnel with the 
correct training are necessary to remove these 
fasteners, refer to your nearest Perkins distributor. 

3  Insert the timing pin (A1) through the hole (A5) in 
the fuel pump gear and the slot of the hub (A4). Push 
the pin fully into the hole (A3) in the body of the fuel 
pump. If the pin can be fully inserted then the pump 
timing is correct. There should be no resistance when 
the pin is inserted.

Note: The position for the timing pin for Lucas and 
Stanadyne fuel injection pumps is (A1). The position 
for the timing pin for Bosch EPVE fuel injection pumps 
is (B1).

4  Remove the timing pin.

5  If the timing pin cannot be pushed into the pump 
body, check that the engine is correctly set at TDC on 
the number 1 cylinder compression stroke

, see 

operation 17-1

 or 

operation 17-2

.

If the engine is set correctly at TDC on the number 1 
cylinder compression stroke, but the pin does not fit 
into the hole, the fuel pump must be removed and set 
by a specialist.

6  Fit the gear cover to the cover of the timing case. 
For gear driven coolant pumps: Fit the coolant pump

, 

see operation 21-2

.

A

A0374C

3

4

1

5

2

1

B

A 03 74 /4

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов