Perkins New 1000 Series Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 290

Perkins New 1000 Series Скачать руководство пользователя страница 114

15

114

Workshop Manual, TPD 1350, issue 3

New 1000 Series

To fit

1 Use the three idler gear setscrews to ensure the
correct position of the idler gear hub (A2) with the
lubrication hole (A1) at the top. Push the hub into
position and remove the setscrews.

2 Lubricate the idler gear bushes with clean engine
lubricating oil. Align the timing marks on the idler gear
with the marks on the crankshaft and camshaft gears.
If necessary, rotate the gear of the fuel injection pump
clockwise to align the relevant timing mark with the
marks on the idler gear and slide the idler gear into
position. Check that all the timing marks are in correct
mesh (B), or (C) for engines fitted with a belt driven
coolant pump. Fit the plate and the setscrews to the
idler gear hub and tighten the setscrews to 44 Nm (33
lbf ft) 4,5 kgf m.

3 For engines that use the idler gear assembly with
needle roller bearings - Inspect the components for
wear and other damage and renew them as
necessary. Lightly lubricate the components with
clean lubricating oil before assembly onto the hub. Fit
the hub (D8) as shown in

, go to paragraph 1

. Put the

rear spacer (D7) in position on the hub. Put the rear
thrust washer (D6) in position on the rear spacer. Put
the bearings (D5) in position on the hub in the same
position as they were before they were removed.
Lightly lubricate the bore and thrust washer faces of
the gear (D4) with clean lubricating oil and put the
gear in position on the bearings. Put the front spacer
(D3) in position on the hub then put the front thrust
washer (D2) in position on the spacer. Put the plate
(D1) in position. The plate has TOP stamped on the
front face as the holes in the plate are not equally
spaced. Fit the setscrews and tighten them to 44 Nm
(33 lbf ft) 4,5 kgf m).

Continued

1

2

A

A0312

B

A0129

C

A0307

4

1

2

3

6

5

7

8

D

A0132

Purchased from www.WorkshopManuals.co.uk

«
...
112
113
114
115
116
...
»

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов