manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 207 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 207

Workshop Manual, TPD 1350, issue 3

207

 

20

New 1000 Series

To adjust

20-11

The engine conforms with USA (EPA/CARB) stage 1 
and EEC stage 1 emissions legislation for agricultural 
and industrial applications.

The idle or maximum speed settings must not be 
changed by the engine operator, because this can 
damage the engine or the transmission.

Specialist equipment, which is available at your 
Perkins Distributor, is needed to adjust the idle or 
maximum speed settings. The warranty of the engine 
can be affected if the seals on the fuel injection pump 
are broken during the warranty period by a person 
who is not approved by Perkins.

1  Operate the engine until it reaches its normal 
temperature of operation and check the idle speed. If 
necessary, adjustment can be made by the outer 
adjustment screw (A2). Release the lock nut and 
rotate the adjustment screw clockwise to increase the 
speed, or counter-clockwise to decrease the speed. 
When the speed is correct, tighten the lock nut. The 
setting of the idle speed can change for different 
applications. Normally the correct speed will be given 
in the manufacturer's handbook for the application. If 
it is not given, refer to your nearest Perkins distributor.

Caution: The setting for the maximum no load speed 
can change for different applications. For the correct 
maximum no-load speed, check the emissions data 
plate fitted to the left side of the cylinder block before 
any adjustment is made to the maximum no load 
speed.

2  With the engine at its normal temperature of 
operation, check the maximum no load speed. A 
typical maximum no load speed is 2860 rev/min. If 
necessary, this speed can be adjusted by the inner 
adjustment screw (A1). Release the lock nut and 
rotate the adjustment screw counter-clockwise to 
increase the speed or clockwise to decrease the 
speed. When the speed is correct, tighten the lock nut 
and seal the screw. 

The person who fits the pump must ensure that the 
adjustment screw is suitably sealed against 
interference after it has been set initially.

1

2

A

A0299

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов